CentOS7执行ifconfig Command not found 未找到命令

本文来为各位介绍一下CentOS7执行ifconfig Command not found 未找到命令错误问题的解决办法。

CentOS7刚发布，我忍不住把DELL T410从CentOS6升级到CentOS7。好不容易等安装结束后，立即配置网络，然后在yum源上安装环境。可是执行ifconfig的时候系统提示让我傻了眼：

[root@chaoge ~]# ifconfig
-bash: ifconfig: 未找到命令

这可是新安装的系统，怎么会没找到熟悉ifconfig命令呢？网上搜一下，一大堆人都在说是环境变量问题，但我确信我的/etc/profile设置是对的，于是终于找到一篇文章说是安装下net-tools就好

[root@chaoge ~]# yum install net-tools

已加载插件：fastestmirror

Repository base is listed more than once in the configuration
Repository updates is listed more than once in the configuration
Repository extras is listed more than once in the configuration
Repository centosplus is listed more than once in the configuration
Repository contrib is listed more than once in the configuration
base                                                                                                                                                                                           | 3.6 kB 00:00:00
extras                                                                                                                                                                                         | 3.3 kB 00:00:00
updates                                                                                                                                                                                        | 3.4 kB 00:00:00
updates/7/x86_64/primary_db                                                                                                                                                                    | 2.8 MB 00:00:08
Determining fastest mirrors

软件包 net-tools-2.0-0.17.20131004git.el7.x86_64 已安装并且是最新版本
无须任何处理
因为我已安装过net-tools所以提示我已经安装，现在熟悉的ifconfig又回来了

[root@chaoge ~]# ifconfig
em2: flags=4099<UP,BROADCAST,MULTICAST> mtu 1500
        ether 78:2b:cb:41:9a:03 txqueuelen 1000 (Ethernet)
        RX packets 0 bytes 0 (0.0 B)
        RX errors 0 dropped 0 overruns 0 frame 0
        TX packets 0 bytes 0 (0.0 B)
        TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0

eth0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
        inet 192.168.1.48 netmask 255.255.255.0 broadcast 192.168.1.255
        inet6 fe80::7a2b:cbff:fe41:9a02 prefixlen 64 scopeid 0x20<link>
        ether 78:2b:cb:41:9a:02 txqueuelen 1000 (Ethernet)
        RX packets 82668 bytes 7831470 (7.4 MiB)
        RX errors 0 dropped 153388 overruns 0 frame 0
        TX packets 1276 bytes 204913 (200.1 KiB)
        TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0

lo: flags=73<UP,LOOPBACK,RUNNING> mtu 65536
        inet 127.0.0.1 netmask 255.0.0.0
        inet6 ::1 prefixlen 128 scopeid 0x10<host>
        loop txqueuelen 0 (Local Loopback)
        RX packets 12 bytes 1071 (1.0 KiB)
        RX errors 0 dropped 0 overruns 0 frame 0
        TX packets 12 bytes 1071 (1.0 KiB)
        TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0

(责任编辑：IT)

搜索

热门标签:

CentOS7执行ifconfig Command not found 未找到命令