CentOS7搭建SAMBA服务器实现与WIN10匿名共享文件
时间:2017-01-17 20:51 来源:linux.it.net.cn 作者:IT
1、安装SAMBA
yum -y install samba samba-client samba-common
2、修改文件打开数
vi /etc/security/limits.conf
最后添加
* soft nofile 65535
* hard nofile 65535
（需重启机器）
3、配置SAMBA
cp /etc/samba/smb.conf /etc/samba/smb.conf.bak #备份
vi/etc/samba/smb.conf
修改为：
[global]
log file = /var/log/samba/log.%m
max log size = 50
security = user
map to guest = Bad User#实现无密码访问
[PyDoc]
path=/root/PythonProject
readonly=yes
browseable=yes
writable = yes
guest ok=yes
4、关闭防火墙
systemctl stop firewalld
systemctl disable firewalld
5、关闭SELinux
修改配置文件需要重启机器：
vi /etc/selinux/config
将SELINUX=enforcing 改为SELINUX=disabled
(需重启机器)
5、测试配置文件
testparm
6、启动SAMBA
systemctl restart smb #重启
systemctl enable smb #修改为开机启动
systemctl status smb #查看状态
7、在windows下输入\\192.168.49.200访问
8、解决win10无法访问共享文件夹
a、开启网络发现
b、开启SMBv1
To enable SMBv1 on the SMB client, run the following commands:
sc.exe config lanmanworkstation depend= bowser/mrxsmb10/mrxsmb20/nsi
sc.exe config mrxsmb10 start= auto
c、开启SMBv1
To enable SMBv2 and SMBv3 on the SMB client, run the following commands:
sc.exe config lanmanworkstation depend= bowser/mrxsmb10/mrxsmb20/nsi
sc.exe config mrxsmb20 start= auto
(责任编辑：IT)
1、安装SAMBA yum -y install samba samba-client samba-common
vi /etc/security/limits.conf 最后添加 * soft nofile 65535 * hard nofile 65535 （需重启机器） 3、配置SAMBA cp /etc/samba/smb.conf /etc/samba/smb.conf.bak #备份 vi/etc/samba/smb.conf 修改为： [global] log file = /var/log/samba/log.%m max log size = 50 security = user map to guest = Bad User#实现无密码访问 [PyDoc] path=/root/PythonProject readonly=yes browseable=yes writable = yes guest ok=yes 4、关闭防火墙
systemctl stop firewalld
systemctl disable firewalld
5、关闭SELinux 修改配置文件需要重启机器： vi /etc/selinux/config 将SELINUX=enforcing 改为SELINUX=disabled (需重启机器) 5、测试配置文件 testparm 6、启动SAMBA
systemctl restart smb #重启
systemctl enable smb #修改为开机启动
systemctl status smb #查看状态
7、在windows下输入\\192.168.49.200访问 a、开启网络发现 b、开启SMBv1 To enable SMBv1 on the SMB client, run the following commands: sc.exe config lanmanworkstation depend= bowser/mrxsmb10/mrxsmb20/nsi sc.exe config mrxsmb10 start= auto c、开启SMBv1 To enable SMBv2 and SMBv3 on the SMB client, run the following commands: sc.exe config lanmanworkstation depend= bowser/mrxsmb10/mrxsmb20/nsi sc.exe config mrxsmb20 start= auto (责任编辑：IT) |