ubuntu高并发状态内核网络参数调优
时间:2014-09-16 10:02 来源:linux.it.net.cn 作者:it
调优方法与目的：
调整linux(ubuntu8.0.4)内核参数以便满足高并发访问，解决大量time_wait和syn攻击问题。
1. 编辑sysctl.conf
sudo vi /etc/sysctl.conf
在最下面编辑添加：
复制代码代码如下:
net.ipv4.tcp_fin_timeout = 30
net.ipv4.tcp_keepalive_time = 1200
net.ipv4.route.gc_timeout = 100
net.ipv4.ip_local_port_range = 1024 65000
net.ipv4.tcp_tw_reuse = 1
net.ipv4.tcp_tw_recycle = 1
net.ipv4.tcp_syn_retries = 1
net.ipv4.tcp_synack_retries = 1
net.ipv4.tcp_max_syn_backlog = 262144
net.core.netdev_max_backlog = 262144
net.core.somaxconn = 262144
net.ipv4.tcp_mem = 94500000 915000000 927000000
保存退出
2. sudo /sbin/sysctl -p
立刻生效(实践中有遇到不能立刻生效的，需要重启机器才能生效)
使用如下命令监控当前各状态连接：
复制代码代码如下:
netstat -n | awk ‘/^tcp/ {++S[$NF]} END {for(a in S) print a, S[a]}’
cat /proc/net/sockstat
3. 查看是否有异常日志：dmesg
4. 查看当前IP个数和每IP连接数：
复制代码代码如下:
netstat -an | grep 80 | awk ‘{print $5}’ | awk ‘BEGIN {FS=”:”} NF==2 {print $1} NF==5 {print $4}’ | sort | uniq -c | sort -n
默认值恢复：
复制代码代码如下:
net.ipv4.tcp_fin_timeout = 60
net.ipv4.tcp_keepalive_time = 7200
net.ipv4.route.gc_timeout = 300
net.ipv4.ip_local_port_range = 32768 61000
net.ipv4.tcp_tw_reuse = 0
net.ipv4.tcp_tw_recycle = 0
net.ipv4.tcp_syn_retries = 5
net.ipv4.tcp_synack_retries = 5
net.ipv4.tcp_max_syn_backlog = 1024
net.core.netdev_max_backlog = 1000
net.core.somaxconn = 128
net.ipv4.tcp_mem = 853440 1137920 1706880
以上配置在实际生产环境中单机1.7w连接数情况下nginx工作正常。
(责任编辑：IT)
调优方法与目的：
1. 编辑sysctl.conf
复制代码代码如下:
net.ipv4.tcp_fin_timeout = 30
net.ipv4.tcp_keepalive_time = 1200 net.ipv4.route.gc_timeout = 100 net.ipv4.ip_local_port_range = 1024 65000 net.ipv4.tcp_tw_reuse = 1 net.ipv4.tcp_tw_recycle = 1 net.ipv4.tcp_syn_retries = 1 net.ipv4.tcp_synack_retries = 1 net.ipv4.tcp_max_syn_backlog = 262144 net.core.netdev_max_backlog = 262144 net.core.somaxconn = 262144 net.ipv4.tcp_mem = 94500000 915000000 927000000 保存退出
2. sudo /sbin/sysctl -p
复制代码代码如下:
netstat -n | awk ‘/^tcp/ {++S[$NF]} END {for(a in S) print a, S[a]}’
cat /proc/net/sockstat 3. 查看是否有异常日志：dmesg 4. 查看当前IP个数和每IP连接数：
复制代码代码如下:
netstat -an | grep 80 | awk ‘{print $5}’ | awk ‘BEGIN {FS=”:”} NF==2 {print $1} NF==5 {print $4}’ | sort | uniq -c | sort -n
默认值恢复：
复制代码代码如下:
net.ipv4.tcp_fin_timeout = 60
net.ipv4.tcp_keepalive_time = 7200 net.ipv4.route.gc_timeout = 300 net.ipv4.ip_local_port_range = 32768 61000 net.ipv4.tcp_tw_reuse = 0 net.ipv4.tcp_tw_recycle = 0 net.ipv4.tcp_syn_retries = 5 net.ipv4.tcp_synack_retries = 5 net.ipv4.tcp_max_syn_backlog = 1024 net.core.netdev_max_backlog = 1000 net.core.somaxconn = 128 net.ipv4.tcp_mem = 853440 1137920 1706880 以上配置在实际生产环境中单机1.7w连接数情况下nginx工作正常。 (责任编辑：IT) |